27.08.2019

Windows 98 Boot Disk

  1. Windows 98 Boot Disk Files

Aug 18, 2005 - Hello All, I remember seeing it in a post under hardware where ya can go to dl the win98 boot disk, but I cant remember which thread it was.

A Windows 98 Startup Disk is a considerable improvement on that produced by earlier versions of Windows, not least because it contains a number of generic, real-mode ATAPI CD-ROM and SCSI drivers that allow CD-ROM devices to become available when running Windows 98 from the Startup Disk. However, it is not guaranteed that one of these drivers will work with any CD-ROM device. Rather, they are provided as a replacement in the event that the real-mode drivers that came with your CD-ROM are unavailable. If you’re unlucky, and your CD-ROM drive doesn’t work with any of the generic drivers on the Windows 98 Startup Disk – or if you don’t want to take the chance that it will – you can actually add the specific real mode driver for your drive to the disk.

Real mode refers to an operating mode of x86 chips that replicates the memory management used by 8086 or 8088 chips, characterised by an absence of memory management or memory protection features and limiting the processor to 1MB of memory. MS-DOS runs in real mode, and the phrase is often used to describe 16-bit MS-DOS device drivers.

The biggest problem is doing this is often locating your CD-ROM drive’s real mode driver in the first place. If you’re lucky, you’ll have this either on a floppy disk or CD-ROM that came with your drive. If you haven’t, and the machine on which you’re planning to do the clean reinstall on is still operational, you may be able to find the driver you’re looking for there.

The place to look is the config.sys file in the root folder of your C: drive. If this contains a line that looks something like …

device=c:cdromgscdrom.sys /d:mscd000 /v

… and the gscdrom.sys file is where it says it is, you’re in luck.

If you can’t locate the real mode driver you need on floppy or CD-ROM media or on your hard drive, the next place to try is the Internet. To do this, you’re first going to have to identify your CD-ROM drive model. To do so, you need to find out precisely what model of CD-ROM drive it is that you have.

To do this you’ll need to remove its securing screws and the EIDE and PSU cables plugged into the back of the drive. Slide the drive out of its bay and you ought to be able to find a sticker somewhere on its casing that identifies its unique FCC ID.

We’ll use BEJCRD-8322B as an example of how to locate a download of the associated real mode driver and how to add it to your Windows 98 Startup disk.

  • Win 98 If you haven't already Partitioned and made the USB Stick Active you may need to create a Bootable CD with Fdisk.exe on it to prepare the USB Stick if you haven't a Floppy Drive.
  • About Windows 98; Boot Disk Contents. Download Disk Contents; Download Boot Disks; Windows Millennium. About Windows ME; Boot Disk Contents; Download Boot Disks.

Details about any equipment displaying such a label label can be found in the Federal Communications Commission database:

Type in the FCC ID as shown above and, so long as the database has a record of it, you’ll be able to access all sorts of useful product documentation:

However, for information concerning the availability of downloadable drivers, you’ll need to visit a specialist driver site such as missingdrivers.com. Click on the CD-ROM Drivers category to locate the manufacturer you’re after:

Click on it and if you’re even luckier, you’ll see the model number you’re looking for:

The real mode driver is the one identified as being a 16 bit DOS driver. When you download and unpack the CDROM.ZIP file, you’ll have a set of files like these. The Gscdrom.sys file is the real mode driver.

What you need to do now is copy Gscdrom.sys and the associated unzipped driver files to a folder on your Windows 98 Startup Disk and edit its Config.sys and Autoexec.bat files.

The portion of the Config.sys file that you’re interested in are the lines marked as [CD], where the set of generic CD-ROM drivers are referenced.

Using a text editor such as Wordpad, add a line that references the gscdrom.sys file.

The /D:mscd001 /v part of the line renames the driver when it is loaded into memory. The important thing here is to ensure that the Autoexec.bat file references this by the same name as the Config.sys file.

Your Windows 98 Startup Disk should now be guaranteed to work with your CD-ROM drive.

This guide is about boot (or startup) disks for the following Windows versions: Windows XP, Vista, 7, 8, 8.1 or 10.

Contents

  • 4 Create boot disk for Windows Vista
  • 6 Create boot disk for Windows 8/8.1/10
  • 7 More Information

What is a boot disk

A boot disk (or a startup disk) is a recovery media (CD, DVD or floppy disk for older Windows versions) that you can use to start Windows, if it became damaged or corrupted somehow.

The term “boot disk” was mostly used in connection with Windows XP (and older versions) and, in some cases, with Windows Vista. For Windows 7, Windows 8 and Windows 10 the “boot disk” term is mostly replaced with the term “recovery disk” (sometimes also named as a “repair disk” or “restore disk”).

NeoSmart Technologies has extensive guides on how to create recovery media for all major PC manufacturers that have their own software for recovery procedures and a recovery disk for all Windows versions (XP, Vista, 7, 8, 10).

If you have a computer from any of the following manufacturers, read that guide too. Most PC manufacturers with computers that have Windows installed also have a recovery partition that you can make use of to restore or repair your computer. Some older models had only a recovery disk (as a CD, DVD etc.) or only the recovery partition.

Our list of recovery media guides for specific PC manufacturers: Dell (including the guide on the recovery partition), Acer, Asus, Gateway, Toshiba, HP, Lenovo.

A boot or startup disk is not an installation disk! You can not use a boot disk to install Windows. To install Windows, use your original Windows installation disk.

You can use the following formats to create a disk:

  • CD or diskette (floppy disk) for Windows XP
  • CD or DVD for Windows Vista
  • CD or DVD for Windows 7
  • CD or DVD or USB for Windows 8
  • USB for Windows 8.1 or Windows 10

Download boot disk

If you aren’t able to boot into Windows or don’t access to the recovery partition to create a system recovery disk, you can use our recovery and repair disk Easy Recovery Essentials to repair and restore your computer.

Easy Recovery Essentials is compatible with the following Windows versions: Windows 10, Windows 8 or 8.1, Windows 7, Windows Vista, Windows XP or Windows Server 2003, 2008 and 2012.

Features of Easy Recovery Essentials include:

  • Automatically find and fix boot errors
  • Works even when you can’t get into Windows
  • Recover from virus infections
  • Restore your PC to a working state
  • Access and backup your important data
  • Advanced tools for IT experts

Easy Recovery Essentials is an ISO download image ready to be burned directly to a CD, DVD or a USB flash drive.

Windows 98 Boot Disk

With Easy Recovery Essentials you can:

  • Find and fix errors automatically with Automated Repair
  • Recover your PC from infections with the built-in antivirus
  • Restore your PC to a working state
  • Access and backup your most important data (like documents, pictures, music, videos and so on)

Note: Easy Recovery Essentials can not be used to install or reinstall Windows.

Windows XP users

Easy Recovery Essentials can be used as a boot disk (or recovery disk) for computers with Windows XP installed to repair the computer, including the full list of Windows XP editions with Service Packs installed:

  • Microsoft Windows XP SP1 (Service Pack 1)
  • Microsoft Windows XP SP2 (Service Pack 2)
  • Microsoft Windows XP SP3 (Service Pack 3)

It’s compatible with both the Home and Professional editions of Windows XP:

  • Microsoft Windows XP Home
  • Microsoft Windows XP Professional

Windows Vista users

Easy Recovery Essentials works with Windows Vista computers and the version for the x86 and x64 platforms. It works with all Windows Vista editions, including the 32-bit and 64-bit editions:

  • Microsoft Windows Vista Ultimate (32-bit and 64-bit editions)
  • Microsoft Windows Vista Enterprise (32-bit and 64-bit editions)
  • Microsoft Windows Vista Business (32-bit and 64-bit editions)
  • Microsoft Windows Vista Home Premium (32-bit and 64-bit editions)
  • Microsoft Windows Vista Home Basic (32-bit and 64-bit editions)
  • Microsoft Windows Vista Starter (32-bit edition)Note: Windows Vista Starter doesn’t have a 64-bit edition.

It’s compatible with the available Service Packs of Windows Vista:

  • Microsoft Windows Vista Service Pack 1 (SP1)
  • Microsoft Windows Vista Service Pack 2 (SP2)

Windows 7 users

Easy Recovery Essentials is compatible with Windows 7 and supports both x86 and x64 platforms and is compatible with the full list of Windows 7 editions, including the 32-bit and the 64-bit:

  • Microsoft Windows 7 Ultimate (32-bit and 64-bit editions)
  • Microsoft Windows 7 Enterprise (32-bit and 64-bit editions)
  • Microsoft Windows 7 Professional (32-bit and 64-bit editions)
  • Microsoft Windows 7 Home Premium (32-bit and 64-bit editions)
  • Microsoft Windows 7 Home Basic (32-bit and 64-bit editions)
  • Microsoft Windows 7 Starter (32-bit edition)Note: Windows 7 Starter is only available in the 32-bit edition.

It’s compatible with the Service Pack 1 for Windows 7:

  • Microsoft Windows 7 Service Pack 1 (SP1)

500 days of summer soundtrack youtube. Windows 8 or 8.1 users

You can use Easy Recovery Essentials as a boot or startup disk (now known as a recovery media) for computers with Windows 8/8.1 installed to repair or restore your computer.

It supports the x86 and x64 platforms and all the Microsoft Windows 8 editions (8 and 8.1), including the 32-bit and the 64-bit editions:

  • Microsoft Windows 8 (32-bit and 64-bit editions)
  • Microsoft Windows 8.1 (32-bit and 64-bit editions)

Windows 10 users

You can use Easy Recovery Essentials as a boot or startup disk (now known as a recovery media) for computers with Windows 10 installed to repair or restore your computer.

Create boot disk for Windows XP

The original Windows XP installation CD itself acts as a boot or startup disk that you can use and run Recovery Console (Command Prompt) to repair your computer with.

If you already have the installation CD, follow these steps to boot into Recovery Console and the Command Prompt of Windows XP:

  1. Insert the CD in the disk drive and restart your computer
  2. Press any key, when prompted to boot from the CD
  3. Press R to open Recovery Console, at the “Welcome to Setup” screen

    Windows XP Press R for Recovery Console

  4. Type your administrator password
  5. Command Prompt should now be available
  6. The following commands might help fix your computer:
  7. Press Enter after each command

If you don’t have the CD, you can create a bootable diskette if your computer has a floppy disk drive to boot into MS-DOS. You need to be able to boot into Windows XP to create this diskette.

To create the boot diskette for Windows XP, follow these steps:

  1. Insert a diskette in your computer’s floppy disk drive
  2. Go to My Computer
  3. Right click on A:, this is usually the drive letter that holds the diskette
  4. Click Format
  5. Check the “Create an MS-DOS startup disk” option
  6. Click Start

Once you have the diskette created, follow these instructions to use it when you need it:

Windows 98 Boot Disk Files

  1. Make sure the disk is in write-protect mode
  2. Insert the disk in the floppy disk
  3. Restart your computer
  4. Follow the instructions on the screen as you boot the system from the diskette

You can also create a set of setup/boot disks that will allow you to bypass the need for a bootable CD-ROM (and then continue a reinstallation of Windows XP) by following these instructions:

  1. Download the setup program file for the Windows XP you have installed:
  2. Extract the files
  3. Type the drive where your floppy disks is – example: A: – and hit Enter when you receive this message:
  4. Insert the first blank disk in the floppy drive when you receive this message:
  5. Continue with the process until all 6 disks are created
  6. Boot from the first created diskette. Make sure you have the installation CD at hand to be used during a reinstallation process.

Create boot disk for Windows Vista

If you already have the Windows Vista installation disk, you can use it to recover or restore your computer.

If not, go to the Create the disk section instructions to learn how you can create the disk (read Prerequisites before).

If you don’t have the installation disk and can’t boot into Windows, go to Download boot disk and use Easy Recovery Essentials’ Automated Repair function to fix boot errors automatically.

To repair your computer, if you have the Windows Vista installation disk, follow these steps:

  1. Insert the disk
  2. Restart your computer
  3. Press any key to start Windows from the disk. If the “Press any key” message doesn’t appear, please check your BIOS settings as you need to boot from the DVD first.

    Press any key

  4. Choose your language preferences
  5. Click Next
  6. Click Repair your computer

If you don’t have the installation disk, but your computer has the recovery options preinstalled, you can follow these steps:

  1. Restart your computer. Remove all CDs, DVDs or USB flash drives from your computer first.
  2. Press and hold the F8 key as your computer boots up. You need to press this key before the Windows Vista logo appears on your screen.
  3. At the Advanced Boot Options screen, select Repair your computer.

    If the “Repair your computer” option isn’t available, your computer doesn’t have any recovery options preinstalled. If so, go to Download boot disk.

  4. Hit Enter
  5. Select a keyboard layout
  6. Click Next
  7. Login with an administrator account (or any account that has administrative rights to the system)
  8. Click OK

If you want to create a boot disk, follow the instructions from Prerequisites and then the Create the disk instructions.

Prerequisites

You must verify what version of Windows Vista you have before you create the boot or startup disk. If you have any Service Packs installed, you need the recdisc.exe file from the System32 folder to be from a Windows Vista system without any Service Packs (SP) installed.

To verify this, follow these steps:

  1. Go to Control Panel
  2. Click on System
  3. Go to the System type section
  4. Check if you run a “32-bit” Windows Vista or a “64-bit” Windows Vista

    Windows Vista System Type

  5. Above, at the Windows edition section, check if you have Service Pack 1 or Service Pack 2 installed, or none.

If you have the Windows Vista with Service Pack 1 (SP1) or Service Pack 2 (SP2) installed, you need to replace the recdisc.exe file.

Your Windows Vista has SP1 or SP2 installed only if it’s mentioned in the Windows edition section, above the “System type” section.

If you have a Service Pack installed, follow these steps to replace the recdisc.exe file before you continue with the Create the disk section steps:

  1. Copy an original recdisc.exe file from a Windows Vista without SP. This file will be replaced with your current recdisc.exe.
  2. Copy this file to your Desktop
  3. Right-click on the file > Properties
  4. Go to the General tab
  5. Click Unblock. If this option – Unblock – doesn’t exist in the General tab, skip this step.
  6. Click OK
  7. Go to C:WindowsSystem32 (from My Computer > C: > Windows > System32)
  8. Find the recdisc.exe file from this folder
  9. Make sure you have permissions to make modifications to this file. Right-click on this file > Properties
  10. To have a backup of your original recdisc.exe file, rename it to recdisc.exe.backup or similar
  11. Go to the copied recdisc.exe file and copy it (Right-click > Copy)
  12. Paste it in the System32 folder, to overwrite your current recdisc.exe file
  13. If you didn’t renamed the original file, confirm that you want to replace it (click Copy and Replace, when prompted)

Once these steps have been completed, move to Create the disk below to create the boot/startup disk for Windows Vista.

Creating a boot disk

Please read Prerequisites above before continuing with these instructions.

These steps allow you to create the boot or startup disk (a recovery media) for Windows Vista that you can use in emergency cases.

  1. At Start, type recdisc.exe in the search field
  2. When the search results appears, click on the top result item
  3. Insert a blank DVD in the disk tray. You can use CDs or DVDs for this
  4. Select the disk drive from the “Drive:” list
  5. Click Create disc. If after clicking Create disc, the system shows a message about the installation disk – Insert Windows installation disc – you need the original installation disk as your version of Windows Vista is missing the necessary files to continue with the process.
  6. Wait for the recdisc.exe utility software to finish the procedure
  7. Click Close, at the “Using the system repair disc” screen

    Windows Vista – Using the system repair disc

  8. Click OK

Create boot disk for Windows 7

If you already have the original installation DVD of Windows 7, you can use that DVD as the boot disk to repair your computer.

If you want to repair your computer and have the installation disk at hand, follow these steps to boot into the System Recovery Options of your computer:

  1. Insert the installation disk (DVD or USB flash drive)
  2. Restart your computer
  3. Press any key to boot from the disk, when prompted
  4. Choose your language preferences
  5. Click Next
  6. Click Repair your computer

If you don’t have the installation disk, but your system has the system recovery options pre-installed, follow these steps:

  1. Remove all CDs, DVDs and USB flash drives from your computer
  2. Restart the computer
  3. Press and hold the F8 key as your computer boots. You must press and hold the F8 key before the Windows 7 logo appears.
  4. Select Repair your computer, at the Advanced Boot Options screen

    If the “Repair your computer” option isn’t listed, it means that your Windows 7 version doesn’t have the necessary files for this procedure. If so, go to Download boot disk.

  5. Select the keyboard layout
  6. Click Next

You can create the boot disk for Windows 7 by following these steps:

  1. Boot into Windows 7 and login as an administrator or any user who has administrative rights to the system
  2. Insert a blank DVD in the disk tray
  3. At Start, type recdisc.exe in the Search field
  4. Click on the first result, the recdisc.exe item. It should usually be the first result item available.
  5. If the “Create a system repair disc” screen doesn’t show up, follow these steps instead:
    1. Go to Control Panel
    2. Go to Backup and Restore
    3. Click on Create a system repair disc

      Windows 7 – Create a system repair disc item

  6. Select the drive that has the blank DVD in it
  7. Click Create disc
  8. When the process is finished, click Close
  9. Click OK

Create boot disk for Windows 8/8.1/10

In Windows 8 or 8.1, you can refresh, reset or restore your computer. These three actions have different outcomes:

  • Refresh will not affect your files. Windows 8/8.1 will reinstall any applications you installed and create a copy of these applications on your desktop. Even so, backup your data before you do a refresh.
  • Reset will remove all your personal files and delete any settings or configuration you did on your computer.
  • Restore will restore your computer to an earlier point in time, if System Restore is available and enabled.By default, Windows 8/8.1 creates restore points whenever you install new applications or do Windows updates. If you haven’t disabled System Restore, restoring your computer via this utility should work.

If you want to create the boot disk, find the instructions below:

  • If you have Windows 8, not 8.1, follow Create the disk as a CD/DVD
  • If you have Windows 8.1, not 8.0, follow Create the disk as a USB drive. For Windows 8.1 you can only use USB drivers to create the disk.

Refresh

How to refresh the Windows 8 or 8.1 on your computer:

  1. Boot your computer
  2. Go to Settings
  3. Go to Change PC Settings
  4. Click Update and recovery
  5. Click Recovery
  6. Find the Refresh your PC without affecting your files section

    The Refresh your PC option in Windows 8

  7. Click the Get started button at this section
  8. Follow the instructions on the screen

Reset

How to reset Windows 8 or Windows 8.1:

  1. Boot your computer
  2. Go to Settings
  3. Go to Change PC Settings
  4. Click on Update and recovery
  5. Click on Recovery
  6. At the Remove everything and reinstall Windows section, click on the Get started button
  7. Follow the instructions on the screen

Restore

For information on how to restore a Windows 8 or Windows 8.1 system, follow our instructions from the guide we did on Windows System Restore here.

Create the disk as a CD/DVD

If you have Windows 8, and not 8.1, you can use CDs or DVDs to create the boot disk (now commonly known as a recovery media):

  1. Boot into Windows 8 and log in with an administrator account
  2. Unplug any USB flash drives
  3. Insert a blank CD or DVD. It’s recommended that you use DVDs, and not CDs, as you will need lots of CDs in the process, if you choose the CD option
  4. Press the Windows and R key to open the Charm Bar. Or go to the Run utility.
  5. Type recdisc
  6. If the “Create a system repair” screen doesn’t appear, follow these steps instead:
    1. Open Control Panel
    2. Go to Recovery
    3. Click on Create a recovery drive
    4. Click Next
    5. Click Create a system repair disc with a CD or DVD instead to create the disc as a CD or DVD and not as a USB flash drive, at the “Connect a USB flash drive” screen
  7. Select the CD/DVD drive from the list

    Windows 8 – Select CD for System Repair

  8. Click Create disc
  9. Wait for the utility software to finish
  10. Remove the CDs or DVDs from the disk tray, when the process is complete, at the “Using the system repair disc” screen

Create a boot disk as a USB drive

These steps are for Windows 8.1 users which can only use USB flash drives to create the boot/startup disk. You need a USB drive with at least 256 MB in size, blank.

To create the disk, follow these steps:

  1. Boot into Windows 8.1
  2. Press the Windows + R key to open the Charm Bar
  3. Type RecoveryDrive.exe
  4. Select Create a recovery drive
  5. If the Recovery Drive utility doesn’t appear, follow these steps instead:
    1. Go to Control Panel
    2. Go to Recovery
    3. Click Create a recovery drive
  6. Click Next
  7. Click Next, at the Create a recovery drive screen
  8. Select the USB drive from the list
  9. Click Next
  10. Click Create
  11. Wait for the software to finish
  12. Click Finish
Boot

More Information

Support Links

  • Easy Recovery Essentials for Windows – our repair and recovery disk.
    It’s an easy-to-use and automated diagnostics disk. It’s available for Windows 8, Windows 7 and Windows Vista. It’s also available for Windows XP and Windows Server.

    Read more at Windows Recovery Disks.

  • The NeoSmart Support Forums, member-to-member technical support and troubleshooting.
  • Get a discounted price on replacement setup and installation discs: Windows XP, Windows Vista, Windows 7, Windows 8, Windows 10.

Applicable Systems

This Windows-related knowledgebase article applies to the following operating systems:

  • Windows XP (all editions)
  • Windows Vista (all editions)
  • Windows 7 (all editions)
  • Windows 8 (all editions)
  • Windows 8.1 (all editions)
  • Windows 10 (all editions)